(TOY-1966-BAO) Toyota Tundra BG Series Upper Grille Installation Details

(TOY-1966-BAO) Toyota Tundra BG Series Upper Grille

Products : TOY1966-BAO

Install Step #1:
Our project 2010/12 Toyota Tundra in need of a custom GrillCraft Grille.
Install Step #2:
Locate all hardware included with your Billet Grille.
Install Step #3:
Open the hood and remove the (10) 10mm bolts holding the grill shell to the hood. The grill will still be held in with clips near its top(clips pop out with a gentle pull).
Install Step #4:
Remove the two 10mm bolts holding the hood latch assembly to the grille.
Install Step #5:
This is what your grill shell should look like once removed from the vehicle.
Install Step #6:
An included bracket, screw and nut will be needed for the next steps. They will screw together on the grill shell as shown.
Install Step #7:
Place the appropriate billet piece into the lower opening of the grille shell and hold a bracket behind one of the screw openings.
Install Step #8:
Drop in a screw through the screw hole and then through the bracket behind.
Install Step #9:
The bracket should be placed behind the grill with the nut threaded onto the screw as shown.
Install Step #10:
Using a wrench and Phillips screw driver, tighten the grill to the shell. Be sure not to over-tighten. Repeat steps 8-10 on the other side of the grille.
Install Step #11:
Place the appropriate billet grille into the upper opening of the grille shell.
Install Step #12:
Insert a screw into the tab on the grill for the bracket to be screwed into place.
Install Step #13:
Place the bracket as shown through the screw.
Install Step #14:
Thread on a nut and tighten the billet grill onto the grill shell. Repeat steps 12-14 on the other side.
Install Step #15:
Place one of the two smaller billet grilles into the middle opening of the grill shell. If it does not fit flush, you might either need to use the other included bracket or re-orientate the grille in the opening.
Install Step #16:
Place a screw through the tab on the grill for a bracket to be attached onto the back of the grill shell.
Install Step #17:
Place a bracket through the screw and attach it as so onto the grille shell.
Install Step #18:
Thread on a nut and tighten the billet grille to the grill shell. Repeat steps 15-18 on the other side.
Install Step #19:
For the upper most billet grill, you're going to need to remove the plastic trim piece in the grille shell.
Install Step #20:
Using a Flat Head screwdriver, bend back the tabs holding the trim piece to pop it out.
Install Step #21:
(OPTIONAL) If your grill shell is chrome or any other light color, you might want to paint the back recess black to contrast the billet grill. Here it is taped up.
Install Step #22:
Here's the recess sprayed black.
Install Step #23:
Place the upper most Billet Grille into the opening and place a screw through the opening.
Install Step #24:
Using a flat nut on the back of the grille, tighten the grill to the shell. Repeat steps 23-24 on the other side.
Install Step #25:
Install the grill shell onto the vehicle, and You're Done! Our project 2010/12 Toyota Tundra shown here with GrillCraft BG Series upper & lower billet grille inserts installed. Shown with Optional GrillCraft Lower 3 Piece Billet Grilles.
Install Step #26:
Our project 2010/12 Toyota Tundra shown here with GrillCraft BG Series upper & lower billet grille inserts installed. Shown with Optional GrillCraft Lower 3 Piece Billet Grilles.

These installations steps pertain to the following vehicles:


Year Make Model Submodel Fitment Notes
2013 Toyota Tundra Base N / A
2013 Toyota Tundra Limited N / A
2013 Toyota Tundra Platinum N / A
2012 Toyota Tundra Base N / A
2012 Toyota Tundra Limited N / A
2011 Toyota Tundra Base N / A
2011 Toyota Tundra Limited N / A
2011 Toyota Tundra SR5 N / A
2010 Toyota Tundra Base N / A
2010 Toyota Tundra Limited N / A
2010 Toyota Tundra SR5 N / A